What kind of oil to pour into the salute walk-behind tractor

73888 07/28/2019 6 min.
Availability of walk-behind tractor

in personal farming, few people can be surprised, because this technical device has been known since Soviet times.
Thanks to him, it became possible to quickly and efficiently cultivate the soil
, which previously took quite a long time and also took a lot of effort.

However, in order for your walk-behind tractor, as they say, to serve you faithfully, regularly plowing the ground and performing its other functions, you need to operate it correctly.

In particular, you need to know how much oil to pour into the gearbox of a walk-behind tractor so that it works in optimal mode, and its parts do not wear out due to the lack of necessary lubrication.

In principle, all the necessary information, as a rule, is indicated in the operating instructions for a specific walk-behind tractor model, where the brands and grades of recommended oils are directly indicated.

However, there are cases when a walk-behind tractor is purchased second-hand

, or in another way, but the point is that such walk-behind tractors are supplied mainly without any instructions.

A person may be at a loss, not knowing what kind of oil is poured into the gearbox of a walk-behind tractor, so it will be useful for him to know about its main types, as well as how to fill it into a walk-behind tractor.

Device

The gearbox is a special device

, included in the design of any walk-behind tractor. It is this part that is responsible for converting and transmitting torque that is generated from mechanical transmissions. In fact, the gearbox powers the walk-behind tractor, making it work.

The service life of the entire walk-behind tractor, as well as its normal functioning, will depend on its quality, as well as on the correct lubrication of its components.

For more details about the gearbox, watch the video:

Depending on the model of the walk-behind tractor, be it one or some other, the gearboxes may differ from each other in some design features. Conventionally, gearboxes can be divided into several types:

• Angular reducers. Such units are quite effective and allow you to couple the engine and transmission.

• Gear reducers. In this case, the gearbox transmission acts as a kind of intermediary between the engine and the wheelbase of the walk-behind tractor.
• Reduction gearboxes. These units achieve an increase in power indicators by reducing the total number of revolutions. Such gearboxes are most preferable because their design includes an air cooling system, which allows them to operate at maximum loads.
• Reverse gearboxes.
  The main advantage of such gearboxes is the ability to reverse the walk-behind tractor. However, units equipped with this type of gearbox do not show high performance indicators and speeds.

Regardless of which gearbox is used in the design of the walk-behind tractor, they all consist of almost the same components:

• gear housing;
• flange and its fastening;
• pulley with V-belt drive (or chain);
• ball bearing;
• stars;
• drain plug;
• steel washer and nut;
• input shaft

These components traditionally form the gearbox itself. Their performance will depend on how well they are

and service life.

Otherwise, if there is insufficient lubrication, the parts will wear out greatly, because they come into contact with each other during operation, and the resulting friction negatively affects their surface.

What kind of oil is poured?

Many people are interested in what kind of oil to pour into the gearbox.

walk-behind tractor? To answer this question, you need to take into account several factors, the main one of which is the manufacturer's recommendation regarding the type of oil.

You also need to be guided by price, without buying very cheap liquids, because they are unlikely to be of adequate quality.

No matter how reliable the original tracks of a snowmobile are, sooner or later during active use of the machine there is a need to replace them. all about snowmobile tracks from the Composite company.

A garden sprayer is an indispensable assistant in pest control. By clicking on you can get acquainted with the gasoline backpack garden sprayer.

MAZ-5337 appeared in the second half of the eighties of the last century. is a versatile, powerful and very reliable truck.

In the store you should also pay attention to the degree of viscosity of the oil, which is indicated on the packaging. In addition, there are special additives - substances that increase the beneficial properties of the lubricant.

In general, oils can be of various types:

• SAE.
  These types of oils cope very well with sudden temperature changes, so they can be used all year round.
• The selection process is as follows: you need to look at the number in front of the letter W - a lower value will indicate that the oil is very well adapted to low temperatures (the smallest is 0W). If the letter W is not on the label, then this oil is suitable for the summer period.
• API.
  In this case, the letters in the marking will indicate the type of engine - gasoline or diesel. Accordingly, a certain letter will indicate that the oil is suitable for gasoline units, and another – for diesel units.
• The numbers will indicate the type of engine ,
  i.e. number 4 means the oil should be used for a 4-stroke engine, etc. The EC value is the degree of energy conservation, i.e. The higher the value, the better the quality of the oil.
• ASEA.
  The highest number in the labeling will indicate that the oil can function in very difficult conditions.
• GOST 17479, 1-85
  . These indicators characterize the degree of viscosity of the oil. As a rule, alphabetic and numerical values ​​are written after this parameter, and their absence indicates that the oil is universal.

Transmission oils for filling into gasoline and diesel walk-behind tractors

As for the gearbox, transmission oils must be used to fill it.

For example, a good choice would be semi-synthetic oil ZIC 10W40, intended for gasoline and diesel walk-behind tractors. API indicator – SM/CF, ACEA – A3/B3, A3/B4, C3.

It is usually sold in 4-liter containers, the cost of which is in the range of 890-950 rubles.

Another decent oil is Super T-3 85W-90 from Gazpromneft. Its technical data will be as follows:

• API indicator – GL-5;
• viscosity degree – 85W90;
• temperature indicator of loss of fluidity – -280C;
• flash point – 2170C;
• package length – 270 mm;
• packaging width – 130 mm;
• packaging height – 240 mm.

This gear oil is also supplied in 4-liter containers, the cost of which is approximately 600 rubles.

This is not the entire list of oils that can be poured into the gearbox of a walk-behind tractor. In principle, anyone who has become familiar with the basic parameters of the oil can independently determine what is needed for their walk-behind tractor.

How to properly dilute fuel for a walk-behind tractor

The main difference between a two-stroke walk-behind tractor is that it does not have a separate lubrication system. For this reason, oil is mixed with gasoline. This oil-gasoline mixture forms a special mist during operation of the device, and it, in turn, processes all parts of the walk-behind tractor in its path.

Types of lubrication possible for walk-behind tractors

Oil is no less important component than gasoline. The stable operation of all equipment components depends on quality. The main purpose of lubrication is to eliminate unnecessary friction. A good product must meet several requirements:

• during combustion, a minimum of ash should be formed;
• upon contact, decomposes quickly;
• quickly dissolves in gasoline;
• good fluidity (relevant for engines with separate supply of oil and gasoline);
• anti-corrosion, temperature, anti-wear properties.

When choosing oil, pay attention to seasonality. The lubricant is:

1. Summer. It has high viscosity and ensures good operation of the cultivator in hot weather.
2. Winter product. The manufacturer labels winter products with a symbol in the form of the letter “W”. The viscosity of the product is lower, which ensures comfortable operation in cold weather.
3. All-season type. A very popular type of oil as it can be used at any temperature.

Note! When purchasing all-season lubricant, take into account that there are options with different viscosity levels. When choosing, use the rule: the stronger the frost, the lower the viscosity level should be.

How to mix gasoline and oil

Proportions used for mixing. The classic proportion a is the ratio of 1 part lubricant to 4 parts gasoline. Specific values ​​are indicated in the manufacturer's instructions.

The fuel mixture is diluted in a separate container. The container must be dry, petrol-resistant and clean. First, you should pour gasoline into the tank, and then add oil. Only after thorough mixing is the resulting composition poured into the tank of the walk-behind tractor.

For walk-behind tractors, gasoline up to 92 octane is used. When mixing, do not fill the tank completely; leave a gap of 2-3 cm (fuel expands when mixed).

How much to fill?

Another important point is the amount of oil needed. Before answering the question - how much oil should be poured into the gearbox of a walk-behind tractor, for example, you must first check the oil level

in the gearbox. To do this, you need to perform certain actions:

• It is necessary to place the walk-behind tractor on a flat surface so that its wings are strictly parallel to this surface.
• We take a wire or rod about 70 cm long, which will act as an oil dipstick.
• We bend the improvised probe into an arc.
• We insert the resulting dipstick into the filler hole to the very end, i.e. all the way. After that we pull it back out.

If the wire is 30 cm deep in oil, then this is the optimal indicator, i.e. no need to add oil. If it is a little less, then it is necessary to top up within these values.

If the gearbox is completely dry, then you will need at least two liters of gear oil.

How to fill oil into a walk-behind tractor gearbox

Before pouring new oil into the gearbox, you need to drain the old fluid.

. This is exactly how the oil is changed in the gearbox of the Salyut walk-behind tractor, a video of which can be found on the Internet, as well as other models of walk-behind tractors.

The algorithm of actions will be as follows:

• The walk-behind tractor needs to be installed on some hill so that the oil can be easily drained from the gearbox.
• There are two plugs on the gearbox - a drain plug, which is located at the bottom of the gearbox, and a plug that closes the oil filling hole. First, unscrew the filler plug, which is located on top of the walk-behind tractor body (at the gearbox).
• We take a sufficiently capacious container (an old bottle of transmission oil will do), and then place it under the gearbox drain plug.
• Carefully unscrew the drain plug
  , after which the oil will begin to flow into our container. After waiting until the oil has completely drained, screw the drain plug back in. Then tighten it with a spanner of a suitable diameter until it stops.

Oil filling process

• Insert the funnel into the filling hole. Then we take the appropriate gear oil to fill the gearbox.
• Having filled the reducer to the optimal level, screw the plug back. This plug is equipped with a special dipstick, and its length is approximately 10 cm. After we have filled in the oil, we need to check its level. To do this, we tighten this plug-dipstick, after which we unscrew it again and check it.
• If the oil is at the tip of this dipstick, then there is no need to add any more
  .

As a rule, the oil change procedure must be performed every 100 hours of operation of the walk-behind tractor. In some cases, this procedure must be performed every 50 hours.

In other words, the frequency of oil changes depends on the model of the walk-behind tractor, so all the necessary information is in the accompanying documentation for the walk-behind tractor.

Changing the Oil in the Salute Motoblock Engine

Auto mechanic, practicing on agricultural equipment

At this point in time, there are many different models of special equipment that are used for land cultivation in agricultural production. Devices often highlighted here are the salute . This equipment is in great demand among agronomists, but a distinctive feature of walk-behind tractors is the short service life of their motor.

Due to the fact that the build quality is not the best, it is necessary to select models that are equipped with an improved power plant from a more reputable manufacturer. In this case, you need to study the Briggs Stratton engine in detail, also clarify which models can replace it, and how the oil is changed in the engine of a Salute brand walk-behind tractor.

Before you buy this walk-behind tractor, you need to decide on the model

Before carefully considering the function of changing the oil for the Salyut 5 walk-behind tractor, you need to familiarize yourself with the models of power plants that are installed on all these devices. Let's take a closer look at our client's current options:

1. Briggs Stratton (amazing power design, but sometimes lacks power) In some individual cases, power units are of course picky due to a lack of oil.
2. Honda (what our client can do is that the owners of walk-behind tractors with Honda engines are satisfied with the power capabilities of the installation, with such an engine the device feels confident on any arable land).
3. The Salute 100 walk-behind tractor is often equipped with branded Subaru engines (the selection of a Subaru engine, as well as a Honda engine, must be made taking into account comparisons of all features).
4. Devices from the manufacturer Lifan are distinguished by a lower price (special equipment with a Lifan engine has a long service life, but here you need to pay special attention to the spark plugs - they sometimes flood).
5. Asme equipment (another manufacturer that intensively provides high-quality EX 27 motors for Russian walk-behind tractors of the Salyut brand; the engines have excellent properties, their feature is low cost).

With so many power plants, it’s not easy to choose the best option. That is why our client needs to examine the units carefully and completely.

Here is a video you can learn about the engines in salute walk-behind tractors:

Fundamentally! When choosing a unit for your own special equipment, you need to take into account the operating features, because any of the motors has more positive properties in any direction.

READ Disassembling the Gearbox of Motoblock MB 2

Quite often, engines of this brand are installed for the Salyut walk-behind tractor. Let's look at the main distinguishing features of these power plants:

• as a rule, there are gasoline engines that are undemanding to Russian fuel;
• here the pulley for walk-behind tractor
  is made of strong material, which increases the service life of the installation;
• These devices are also characterized by the highest power, which allows you to freely process the soil;
• The Stratton walk-behind tractor Salut 5 is usually equipped with this particular engine, which is why the model has gained popularity.

Also, these devices are characterized by low oil consumption, and today they have a low price. In this case, there is no need for huge investments in repairs and maintenance during operation.

Fundamentally! If a power plant from this manufacturer is installed, it is recommended to frequently check the oil level, because if it is insufficient, the motor will have the shortest service life.

These power structures are widely distributed within the Russian Federation. Let's look at the main distinguishing features of these devices:

• highest power;
• ability to work for a long time at high speeds;
• improved maneuverability;
• highest torque;
• unpretentiousness to Russian fuel;
• reliable assembly and long service life.

These properties distinguish engines from the manufacturer Honda. But, despite the quality, the price of the units is quite high if we associate it with other similar variations of units for Salyut

.

Fundamentally! The engine is characterized by high speeds, which makes it quite voracious compared to other manufacturers of units for similar special equipment.

Another power plant that has gained popularity among owners of special equipment. These models have incorporated into their capabilities all that remains to give our client the positive properties from other manufacturers. Due to the huge number of models released, it is recommended to compare in advance what remains to be done for our client properties, because after installing the Subaru engine, the walk-behind tractor can change significantly. Here you should realize that the devices are quite expensive, but the service life is also higher. Additionally, it must be emphasized that both fuel, gasoline and diesel, are used here. This point should be taken into account when purchasing.

Fundamentally! Subaru engine units have high power and operate at high speeds, which is why at times there may be higher fuel and oil consumption compared to other power plants.

These motors for walk-behind tractors appeared relatively recently, but are already very popular among gardeners and companies involved in agriculture. Let's look at the main relevant features of these motors:

• products are available in various capacities;
• there are both diesel and gasoline units here;
• motors have a long service life;
• moderate power and operating speed;
• quite low price of the devices;
• the versatility of these devices;
• improved traction of Lifan engines;
• small dimensions (motors are easy to install).

READ Walk-behind tractor engine is smoking heavily

Also, these installations are not very voracious during frequent use (the engines do not consume a lot of fuel, in addition to oil, compared to other similar models from other manufacturers).

Changing the oil from a walk-behind tractor engine

Fundamentally! Despite the large list of properties of similar power plants, the models appeared on the Russian market relatively recently, for which reason they were not widely used. Also, during operation, you need to take care of the condition of the spark plugs; there are often cases when they get flooded.

Another manufacturer of power plants for Salyut

. These units are in great demand today. Their production is characterized by the following distinctive features:

• moderate characteristics of power and number of operating revolutions;
• comparatively low price of devices;
• long service life of motors;
• availability of all consumables and spare parts for free sale;
• unpretentiousness to Russian fuel;
• engines don't eat a lot of oil;
• comparatively small size of power plants;
• motors ensure good cross-country ability.

Despite the significant amount of positive aspects, when operating these engines you will also, of course, encounter some shortcomings. The most pronounced of the disadvantages is the overhead of spare parts (in order for the engine to last for a long time, consumables need to be changed quite often). Today, you need to use high-quality oil

, which sometimes has to be topped up, because if there is a shortage of it, the service life of the motor is reduced.

It should be noted that not all brands of motor units for Salyut walk-behind tractors were examined here; there are also other manufacturers of domestic power plants, but their properties and characteristics are somewhat worse than those of the models mentioned here.

ACME is relatively cheap

An internal combustion engine is a complex mechanism consisting of many parts. To ensure reliable and long-term operation of all components of the device, it is necessary to select and fill the engine oil correctly. Here a logical question arises: what kind of oil?

use? While answering this question, it is necessary to clarify what properties such a composition should have:

1. Have sufficient viscosity so that the components can be retained on all elements of the motor.
2. Be resistant to temperature changes (because in service even when the ignition is turned off, this parameter can vary significantly).
3. Do not lose viscosity when the engine heats up to the highest temperature (with accelerated operation of the internal parts).
4. Maintain viscosity for a sufficient time to extend the life of the power plant.
5. Contain active additives that reduce the load on motor components during friction.

READ How to Adjust the Carburetor on a Ural Motoblock

The oil used for the walk-behind tractor must have similar characteristics. Choosing the right product will extend the life of the motor, and today you will not often need to waste money on service. Usually, special oil

, which has high viscosity. Nowadays you should give your professional preference to synthetics because they have a longer service life.

Fundamentally! When using a walk-behind tractor, it is often necessary to maintain the oil level in the engine at a good level; unless you watch this moment, there is a high possibility that the engine structure will fail at some point.

Changing a motor unit or oil, as well as choosing the right components, is a task that few people can cope with when busy. If any difficulties arise, it is not recommended to try to complete the work using the error method. It is recommended to entrust these moments to specialists. The company's employees are ready to do these things. All you have to do is wait for the result, which will appear quickly. The work will be completed quickly and efficiently.

Changing the oil in the gearbox and gearbox of a walk-behind tractor

For our efforts, our organization will only ask for a modest reward. At the same time, the satisfied client will also be provided with a long-term guarantee for the entire range of services that were provided. From the parameters of this, they will conclude that it is harmful to try to understand a complex technological process without the help of others, if you do not have the appropriate knowledge and abilities, it is much easier to entrust what our client can do to the experts, during the period of their work - to enjoy their vacation.

What oil should I fill the engine block with?

First, you need to read the instructions for the device model you are using. This is where it is indicated what kind of oil is poured into the walk-behind tractor

and
how many
. Such rules must be strictly observed. First, you need to find out which motoblob is the best. If you choose a diesel vehicle, you must use diesel fuel accordingly. Also, pay attention to the time of year, as there are summer and winter remedies.

It happens that a person purchases a unit with a gasoline engine without instructions. What to do in this case? In this situation, it is best to buy SAE 30 or 5w30. There are also brands for the winter period. 0w40. But this synthetic oil has a high cost. If it is original, then the engine parts will not wear out.

How to choose?

During operation, the engine block motor is constantly subjected to severe stress. Therefore, it is necessary to purchase products that are of high quality. We must beware of imitation. To improve engine performance, special substances are added to oils. They are called additives, which serve to improve the properties of the lubricant.

There are a large number of technical oil indicators. What oil should I fill the engine block with? When choosing, pay attention to viscosity and quality. These two indicators are key. First of all, choose which motor unit is best to use for this type of object, as well as the climate conditions. The answers to these questions can be found on the motor fluid labeling.

Features of gearbox products

The gearbox oil must be changed regularly. Why do this? After some time, the additives begin to lose their characteristics. In order for them to last for a long time, they must be protected with oil. If you don't replace it, it will cause foaming and the transmission will start to get stuck. But there are vehicles that do not need to be replaced.

To implement your replacement, apply product transfer types. Always check the previous level before you start. Then remove the dipstick and wipe it with a soft cloth. How much oil should the engine block contain? The number must be between the maximum and minimum levels. If the level is too low, it is added.

How to change?

Naturally, if you see that there is not enough oil, then you just need to add it. This can be done either through a funnel, or through a hose, or directly from the neck of the bottle into the neck of the crankcase. Oil is poured into the walk-behind tractor’s crankcase smoothly, without haste.

After topping up, you need to measure the oil level again to make sure it is correct. After this, changing the oil in the walk-behind tractor can be considered complete.

To add engine oil, you need to lean forward a little. To replace the lubricant, there is a special plug in the gearbox. Please note that there is no need to turn over or tilt the walk-behind tractor, as this may cause oil to leak out, which may cause it to enter the engine cylinders.

Owners of walk-behind tractors usually change the oil for the first time after 5 hours of operation on their unit, and then change it every 25 hours. But it is advisable to change the lubricant every spring before first use.

It’s worth thinking about before turning off the oil sensor on your walk-behind tractor, because thanks to it you can also monitor the lubricant level without extraneous tools.

As we have already said, the oil level must meet two criteria: if you measured the level without a dipstick, then add until the oil is visible to the eye through the neck hole. But, in any case, it is advisable to check the level with a dipstick.

To do this, simply lower it into the crankcase and make sure that it is in good condition. This way, you can make sure that there is exactly as much oil as required for the normal operation of the unit.

Cost and reviews

The cost of lubricants for motor blocks depends on the brand of the manufacturer, as well as on their technical characteristics. The price of synthetic oil ranges from 300 to 700 rubles. Many users of walk-behind tractors use products from the brands Stroke, Sae, Rezoil. Such companies are of high quality. But, accordingly, their cost is quite significant.

Proper maintenance and operation of a walk-behind tractor or cultivator helps to extend the service life and improve the performance of the equipment.

The walk-behind tractor gearbox is one of the most important design elements. What kind of oil to pour into the gearbox of a walk-behind tractor or cultivator and the frequency of its replacement, volume - these are data that every owner of such equipment needs to know.

All data is taken from walk-behind tractor manuals and the table contains quotes or exact excerpts from these user manuals. You can download all instructions on the Pahalka website page “Instructions for walk-behind tractors” or on the pages with the characteristics of walk-behind tractors

For a gearbox, not only the brand of oil is important, but also the frequency of maintenance. Several recommendations on the frequency and procedure for changing the oil in a walk-behind tractor gearbox from leading manufacturers:

Let's try to generalize:

• the first oil change in the walk-behind tractor gearbox during break-in - after 25-50 hours of operation
• frequency of oil changes - after 100-250 hours of operation or 1-2 years during storage

The second point is often not taken into account by those who do not carefully read the instructions; as a result, manufacturers of walk-behind tractors complain that buyers in Russia practically do not change the oil in the gearbox; at best, they monitor its level and top it up. If you want your equipment to serve for a long time and reliably follow the manufacturer’s advice.

Remember: There is no need to pour oil into gasoline. The engine is four-stroke, like in a car. Be sure to pour oil into the engine. In a box - definitely. It is necessary to note some points without which it is impossible

Gasoline engines

The Nevsky gasoline engine has the following advantages over diesel engines:

• Easier to maintain;
• Fuel does not freeze in cold weather (for example, if it is necessary to clear an area of ​​snow);
• Suitable for light soil (not virgin soil);
• Has proven itself when working with small sites;
• The noise level of such an engine is lower than that of a diesel engine;
• Lower cost

READ How to Start a Motoblock MB 2

The main problems of a gasoline engine and their elimination

The main problems in the operation of a gasoline engine are:

• A drop in electricity after the walk-behind tractor has been idle (a possible cause of this malfunction. Deposits on the walls of the carburetor and fuel system, which can be eliminated by cleaning and short-term “warm-up” operation at idle);
• Carb blocking (cleared by purification);
• Clogged gas hose (can be cleared by cleaning);
• Clogged air filter (needs cleaning);

If the engine does not start, the probable causes of this condition are:

• The angle of the walk-behind tractor is too large (installed on a flat surface);
• The fuel supply is interrupted (cleaning the fuel system will help);
• Clogged filter (replacement or cleaning recommended);
• Defective spark plug (unscrew, clean, if necessary, replace);

If the gasoline engine stops or malfunctions, this may be due to:

• The engine simply did not warm up;
• The spark plug is dirty (clean and remove carbon deposits);
• The magneto (generator) has failed. Replacement will help;
• White smoke appears (probable cause: Poor quality gasoline or tilt of the walk-behind tractor, oil leaks and gets into the valve, burns there and is a source of smoke).

Servicing gasoline engines. What to look for

The main maintenance work on gasoline engines of Neva walk-behind tractors is:

• Oil level control
• Changing the oil in accordance with the manufacturer's recommendations
• Ignition system control
• Fuel system management
• Air filter service (usually performed after 50 hours). If necessary, such a service can be done earlier, especially if the Neva walk-behind tractor is used in dusty places.

Refueling a gasoline engine is carried out using a brand of oil that is used only for this type of engine or a universal one, suitable for both diesel and Neva gas engines.

The oil level should reach the special mark on the filler neck. Changing the oil in a walk-behind tractor:

The first scheduled oil change in the engines of Neva walk-behind tractors is carried out after 25-50 working hours.

If the walk-behind tractor is used daily, the oil must be changed after 25 hours, if less often, then after 50. The oil must be changed during changing seasons, for example, before spring harvesting or sowing.

operation of walk-behind tractors

Skipper, Brado and the like. The technique is, in principle, unpretentious, but you need to pay attention to some points. So it is better to make the first oil change a short time after purchase. That is, after 8 hours of operation, it is better to change the oil. This is necessary in order to clean the engine of foreign impurities in the form of preservative lubricant and products of the initially grinding mechanisms.

What kind of engine oil

A walk-behind tractor can be filled with almost the same amount as in a car engine, this is due to the same operating principle of the engine (in both cases it is four-stroke with an overhead camshaft).
That is, oil marked SAE 15W40 or SAE 10W40 is quite suitable, and it is advisable to make sure that the oil class is not lower than SF, although all modern oils already meet these requirements. How much to fill? - From 0.6 to 1.1 liters - you need to look at the dipstick or technical characteristics, or more simply at the filler neck: when you see oil there, it means stop soon. It’s easier to say: for a walk-behind tractor 8 horsepower is 0.6 liters, for a walk-behind tractor 10 hp, 14 hp, 16 hp. — About 1.1 liters (after all, the difference between them is mainly the cylinder-piston group) I would also like to clarify (regarding oil): It doesn’t matter what your walk-behind tractor or cultivator is called, what matters is what engine it has. Many people want to change the oil in the Skipper, Stanley, Brado, Hulk, Titan, Luch, Mtz, Zirka, Kronos, Asilak and others walk-behind tractors. And if information on changing the oil for a specific walk-behind tractor is not available, you need to assume that many cultivators are of the same type. And, as for the oil in the engine or in the box, it is worth paying attention to which engine. After all, there are only a few types of engines. In fact, it’s enough to know how much horsepower the power is. Although, suppliers usually indicate this power not entirely correctly, so it is better, of course, to know the markings of your engine. PETROL ENGINE 170F 8 HP (or equivalent to GX210) Engine oil volume: 600 ml Installed on walk-behind tractors: Brado BD-700, walk-behind tractors BD-850, Skiper CK-700, Ck-850, Shtenli 1030, Shtenli 900, FERMER FM-811MX, FERMER FM-909MSL, CENTAUR 2080B, ZID Favorite, Asilak SL-84, PETROL ENGINE 177F 9-10 hp (or equivalent GX 270 Engine oil volume: 1000 ml Installed on walk-behind tractors: Belarus 09N-02, Brado BD-1000, Skiper Ck-1000 , ASILAK SL-101, SL-102,SL-104, SL-105,GRASSHOPPER 177F, Ugra NMB-1N15,Zigzag GT 903, FERMER FM-1011MX, Krones 1100-9, OKA MB-1D2M16, Huter GMC-9.0, Ugra NMB-1N10a, Ugra NMB-1N14 PETROL ENGINE 188F 13 hp (or equivalent GX 390) MTZ Belarus 09N-02, Brado BD-1400, Skiper Ck-1400, ASILAK SL-131,SL-133 SL-144 , SL-145, GRASSHOPPER 188F, FERMER FM-1303, FERMER FM-1311MX, Motor Sich MB-13E, Centaur 2013B, Krones 1100-3D, Shtenli 1100 Pro, Schneider SM-13 PETROL ENGINE 190F 16 hp (or analogue GX 410) Engine oil volume: 1100 ml Installed on walk-behind tractors: Brado BD-1600, Skiper Ck-1600, Shtenli 1600, FERMER FM-1511MX, Bertoni 16D, Asilak SL-151, Centaur 2016B, Krones 1100-16D, Shtenli 1900 Pro, Shtenli 1800 Pro, Profi 1900 Pro

Oil in the gearbox

Filled once for the entire period of operation. Transmission oil, type TAD 17 (according to the international standard, SAE 80W90, SAE 85W90). This refers to the viscosity of the oil. The number 90 means the recommended operating temperature is up to 40 degrees Celsius. Essentially anything, except for very special ones. Preferably transmission. Preferably GL-4. If you plan to use it in winter, 80W is better than 85W. Fill from 1.5 to 2.5 liters - it’s better to look at the technical description, and even better to control it using the dipstick. Focus on a volume of about two liters. In a walk-behind tractor with 8 horsepower - 1.5 liters, 10 hp. - 2.1 liters, 14 hp. - 2.3 liters, 16 hp. - 2.5 liters.

Another important point.

When controlling a walk-behind tractor, when moving it, the question arises: do you need rights to control it?
This is especially interesting when moving independently with a seat adapter. As, for example, with a trailer equipped with a saddle for the driver. The fact is that the walk-behind tractor is an off-road vehicle. That is, it is designed for off-road travel. A driver's license or license is not required to operate a walk-behind tractor, since the walk-behind tractor is not a participant in road traffic. Advertising:

Your comments:

Oil for a diesel walk-behind tractor - features of choice

When choosing engine oil for a diesel walk-behind tractor, you should follow the instructions in the operating instructions.
However, if the instructions for use have been lost, then you will have to study the compositions available on the market more carefully. Motor oils for diesel engines are classified into the following categories. The special markings indicated on the container with lubricant will help determine the type and compliance of the composition for a particular walk-behind tractor:

1. API CJ-4 - compounds with this marking are designed specifically for walk-behind tractors with a capacity of 10 hp or more. With. and more. The composition of these lubricants has increased viscosity, which guarantees the proper operation of all elements of the unit’s motor;
2. API CI-4 - these oils should be used for engines equipped with different types of injection and supercharging. Such oils have good dispersing characteristics and high resistance to thermal oxidation;
3. API CH-4 - lubricants with this marking fully comply with all modern requirements and quality standards. Among the advantages of these compositions, one should highlight the ability to fill them into diesel engines running on fuel in which the sulfur percentage exceeds 0.5%;
4. API CA - compositions of this type are optimally suited in cases where diesel fuel contains a small amount of sulfur. Oils with this marking protect the walk-behind tractor engine from the formation of harmful deposits on its walls;
5. API CB - the use of oils of this oil reduces the risk of corrosion of walk-behind tractor bearings;
6. API CC - such oils will be the best option for an engine equipped with a turbocharger, but without a supercharger. These compounds help walk-behind tractors withstand long-term loads and work properly in difficult conditions;
7. API CF-2 - oils of this group perform well when used in walk-behind tractors that are subject to heavy loads.

After purchasing suitable motor oil, you can proceed to pouring it into the walk-behind tractor engine. The procedure for this is quite simple:

1. First install the unit in a horizontal position;
2. Place a wide container under the drain hole in the engine and remove the plug by carefully prying it off with a screwdriver;
3. Wait until the old oil drains from the engine and screw the plug back into the hole;
4. Pour at least 2 liters of new lubricant inside the engine.

Remember that the oil in new walk-behind tractors should be changed three times at intervals of 5 hours of moderate use. After this, replacement is required no more than once every 25 hours of operation of the walk-behind tractor.